PV Array Combiner Boxes

CIRCUIT/SYSTEM PROTECTION - PV ARRAY COMBINERS

Available from 4 pole to 36 pole with blanking plates included for unused pole spaces. These enclosures are fitted with a small handle for locking the door and can be retrofitted with a key lock assembly. IP65 rated.

The NOARK range of DC Circuit Breakers and Fuses fit these enclosures.

PV-ENC-4P 4 Pole Enclosure

PV-ENC-8P 8 Pole Enclosure

PV-ENC-12P 12 Pole Enclosure

PV-ENC-24P 24 Pole Enclosure

PV-ENC-36P 36 Pole Enclosure

Brochure

MidNite Solar offers a range of PV Combiners to accommodate PV systems as small as a two string off grid cabin and up to 16 strings for a 100KW commercial grid tie inverter. The MNPV series of combiners are the result of 20 years of design and manufacturing experience in the renewable energy industry. Each unit has the same quality features such as:

Aluminium rainproof type 3R enclosure
Internal plastic injection molded dead front covers
Knock outs that accept waterproof strain reliefs, conduit or panel mount MC type connectors
Knock outs for lightning arrestors
Uses 150VDC & 300VDC breakers or 600VDC fuses depending on model number
Adaptable for two separate inverters or charge controllers on certain models

MNPV3 For 150 VDC charge controllers and 600 VDC gridtie inverters

Gray aluminium type 3R rainproof enclosure with insulating deadfront, will accept three 150VDC (MNEPV) breakers or two 600/1000 VDC fuse holders. Includes a 60 amp plus bus bar, 6 position PV negative bus bar and a 6 position ground bus bar. Punch out tabs on the plastic deadfront make for a clean installation using circuit breakers. An included snap in adapter makes for a professional looking installation when installing fuse holders. A single 300VDC breaker from 7 to 50 amps may be installed as a disconnect (no combining busbar) .

The enclosure may be mounted to a pole or wall indoors or out.

Breakers/fuse holders sold separately

MNPV6 For 150 VDC charge controllers and 600 VDC gridtie inverters

Grey aluminium type 3R rainproof enclosure with insulating dead front, will accept six 150VDC breakers or four 600/1000VDC fuse holders. Includes 15 position PV negative bus bar, 14 position ground bus bar, 120 amp Plus bus bar for breakers and 80 amp bus bar for fuses. Punch out tabs on the plastic deadfront make for a clean installation using circuit breakers. An included snap in adapter makes for a professional looking installation when installing fuse holders. Up to three 300VDC breakers from 7 to 50 amps may be installed as a disconnect (no combining busbar).

The enclosure may be mounted to a pole or wall indoors or out. The plus bus bar may be split to support two grid tie inverters or two charge controllers. Gridtie inverters typically can have PV minuses common. Most charge controllers can have PV minuses common.

Breakers/fuse holders sold separately

MNPV12 For 150 VDC charge controllers and 600 VDC gridtie inverters

Grey aluminum type 3R rainproof enclosure with insulating dead front, will accept twelve 150VDC breakers or ten 600/1000VDC fuse holders. Includes 15 position PV negative bus bar, 15 position ground bus bar, and two 200 amp Plus bus bars for breakers or fuses. Plus busbars can be combined or separated to support 2 grid tie inverters or two charge controllers. Charge Controllers and Gridtie inverters can typically have a common PV minus. The exception is the XW and BlueSky.

Snap in adapters are included for use with fuse holders for a professional fit and finish.

Breakers/fuse holders sold separately.